Ritvik "Megabloks" #9761 "Desert Patrol"

  1 - decal sheet, L97611
  1 - instruction booklet, D97611
  4 - 9cm diameter by 3.7cm wide black wheels. (these are very big - bigger
    by far than any Lego ones I've seen. They are fairly hard but do have
    some give to them.)
  2 - 14.3cm black axles. (noticeably thicker than Lego ones)
  1 - 4.5cm soft black tubing (much like Lego pneumatic tubing)
  1 - 10.3cm soft black tubing
  1 - 4 x 4 x 1 lt grey cylinder (very similar to the Lego ones)
  1 - 4 x 4 x 1/3 lt grey cylinder bottom (this has a familiar split
    connector sticking up the middle, which goes into the central bottom tube
    of the above piece, allowing the combination to be a turntable)
  2 - 8 x 16 x 1/2 lt grey plate
  2 - 4 x 16 x 1/2 lt grey plate

8 plastic bags contained the rest of the pieces. I believe 3 of them had
the same contents.

153 - 2 x 4 x 1 tan brick (yep, 153 of them!)
 24 - 2 x 4 x 1 black brick (1 was spare)
  9 - 2 x 4 x 1 lt grey brick (2 were spare!)
  6 - 2 x 3 x 1 tan reverse low slope brick
 38 - 2 x 2 x 1 tan brick
  9 - 2 x 2 x 1 lt grey brick
 28 - 2 x 2 x 1 tan roof brick (1 was spare)
 13 - 2 x 2 x 1 lt grey roof brick
  4 - 2 x 2 x 1 black roof brick
  9 - 2 x 2 x 1 tan reverse slope brick
  3 - 2 x 2 x 1 lt grey reverse slope brick
 41 - 1 x 8 x 1 tan brick (1 was spare)
  4 - 1 x 8 x 1 black brick
 24 - 1 x 4 x 1 tan brick (1 was spare)
 38 - 1 x 2 x 1 tan brick
 21 - 1 x 2 x 1 lt grey brick
  2 - 1 x 2 x 1 clear brick
  6 - 1 x 1 x 1 tan brick
  9 - 2 x 12 x 1/3 tan plate
  4 - 2 x 12 x 1/3 lt grey plate
 49 - 2 x 4 x 1/3 tan plate
 26 - 2 x 2 tan tile (yes, 26 tiles!)
  3 - 2 x 2 transparent green tile
 11 - 2 x 2 x 1/3 tan double top plate (these have lugs on both faces)
 14 - 1 x 4 x 1/3 tan plate
  2 - 1 x 4 x 1/3 lt grey plate
 30 - 1 x 2 x 1/3 tan plate (1 was spare)
 11 - 1 x 2 x 1/3 lt grey plate
 13 - 1 x 1 x 1 lt grey cylinder (3 were spare)
 13 - 1 x 2 x 1 lt grey brick with large round hole on one side (big
    enough for the axles) and double-lug socket on other side
  6 - 1 x 2 x 1 tan brick, as above
  2 - 1 x 2 x 2/3 lt grey brick with side connector (yes, 2/3 high)
  1 - 6.5cm lt grey antenna
 14 - 1 x 1 x 1/3 black round plate (gems) (2 were spare)
  3 - 2 x 2 x 1/3 lt grey plate, with another 2 x 2 x 1/3 attached to one
    edge at right angles. The attachment is flat, with just 4 holes that
    lugs can fit into from either side.
  3 - 2 x 2 x 1/3 lt grey plate with "handle" on one side. The handle is
    at about the next lug position, and is of diameter suitable for clipping
    various little things onto. It runs parallel to the edge of the plate.
  4 - 1 x 1 x 1/3 lt grey round plate with horizontal clip (progs of clip
    in same plane as plate) (1 was spare)
  7 - 1 x 1 x 1/3 lt grey plate with side "axle". This is the same size
    axle as above - things can clip onto it. Useful piece. (1 was spare)
  2 - 1 x 1 x 1/3 lt grey plate with long vertical clip. Much like the
    Lego ones, but the clip extends about a half lug further out.
 11 pair 1 x 4 x 1/3 to 1 x 4 x 1/3 tan hinge plates. One half of each
    has 3 fingers on each end, pointing out from one long edge. The other
    half has two fingers pointing up from one edge of each end. There are
    no lugs on the second piece, just space for them on the bottom.
  2 - 2 x 4 x [2/3 - 2] black hollow box. Sort of like a 2 - high hollow
    2 x 4 brick, except that the sides slope from the 2 height on one
    end down to a height of 2/3 on the other. Decorated as exhaust ports.